FLOSS Manuals

 English |  Español |  Français |  Italiano |  Português |  Русский |  Shqip

CSOUND Português

PHYSICAL MODELLING

With physical modelling we employ a completely different approach to synthesis than we do with all other standard techniques. Unusually the focus is not primarily to produce a sound, but to model a physical process and if this process exhibits certain features such as periodic oscillation within a frequency range of 20 to 20000 Hz, it will produce sound.

Physical modelling synthesis techniques do not build sound using wave tables, oscillators and audio signal generators, instead they attempt to establish a model, as a system in itself, which which can then produce sound because of how the function it producers time varies with time. A physical model usually derives from the real physical world, but could be any time-varying system. Physical modelling is an exciting area for the production of new sounds.

Compared with the complexity of a real-world physically dynamic system a physical model will most likely represent a brutal simplification. Nevertheless, using this technique will demand a lot of formulae, because physical models are described in terms of mathematics. Although designing a model may require some considerable work, once established the results commonly exhibit a lively tone with time-varying partials and a "natural" difference between attack and release by their very design - features that other synthesis techniques will demand more from the end user in order to establish.

Csound already contains many ready-made physical models as opcodes but you can still build your own from scratch. This chapter will look at how to implement two classical models from first principles and then introduce a number of Csound's ready made physical modelling opcodes.

The Mass-Spring Model1 

Many oscillating processes in nature can be modelled as connections of masses and springs. Imagine one mass-spring unit which has been set into motion. This system can be described as a sequence of states, where every new state results from the two preceding ones. Assumed the first state a0 is 0 and the second state a1 is 0.5. Without the restricting force of the spring, the mass would continue moving unimpeded following a constant velocity:

 

As the velocity between the first two states can be described as a1-a0, the value of the third state a2 will be:

a2 = a1 + (a1 - a0) = 0.5 + 0.5 = 1

But, the spring pulls the mass back with a force which increases the further the mass moves away from the point of equilibrium. Therefore the masses movement can be described as the product of a constant factor c and the last position a1. This damps the continuous movement of the mass so that for a factor of c=0.4 the next position will be:

a2 = (a1 + (a1 - a0)) - c * a1 = 1 - 0.2 = 0.8

 

Csound can easily calculate the values by simply applying the formulae. For the first k-cycle2 , they are set via the init opcode. After calculating the new state, a1 becomes a0 and a2 becomes a1 for the next k-cycle. This is a csd which prints the new values five times per second. (The states are named here as k0/k1/k2 instead of a0/a1/a2, because k-rate values are needed here for printing instead of audio samples.)

EXAMPLE 04G01_Mass_spring_sine.csd

<CsoundSynthesizer>
<CsOptions>
-n ;no sound
</CsOptions>
<CsInstruments>
sr = 44100
ksmps = 8820 ;5 steps per second

instr PrintVals
;initial values
kstep init 0
k0 init 0
k1 init 0.5
kc init 0.4
;calculation of the next value
k2 = k1 + (k1 - k0) - kc * k1
printks "Sample=%d: k0 = %.3f, k1 = %.3f, k2 = %.3f\n", 0, kstep, k0, k1, k2
;actualize values for the next step
kstep = kstep+1
k0 = k1
k1 = k2
endin

</CsInstruments>
<CsScore>
i "PrintVals" 0 10
</CsScore>
</CsoundSynthesizer>
;example by joachim heintz

The output starts with:

State=0:  k0 =  0.000,  k1 =  0.500,  k2 =  0.800
State=1:  k0 =  0.500,  k1 =  0.800,  k2 =  0.780
State=2:  k0 =  0.800,  k1 =  0.780,  k2 =  0.448
State=3:  k0 =  0.780,  k1 =  0.448,  k2 = -0.063
State=4:  k0 =  0.448,  k1 = -0.063,  k2 = -0.549
State=5:  k0 = -0.063,  k1 = -0.549,  k2 = -0.815
State=6:  k0 = -0.549,  k1 = -0.815,  k2 = -0.756
State=7:  k0 = -0.815,  k1 = -0.756,  k2 = -0.393
State=8:  k0 = -0.756,  k1 = -0.393,  k2 =  0.126
State=9:  k0 = -0.393,  k1 =  0.126,  k2 =  0.595
State=10: k0 =  0.126,  k1 =  0.595,  k2 =  0.826
State=11: k0 =  0.595,  k1 =  0.826,  k2 =  0.727
State=12: k0 =  0.826,  k1 =  0.727,  k2 =  0.337

 

So, a sine wave has been created, without the use of any of Csound's oscillators...

Here is the audible proof:

EXAMPLE 04G02_MS_sine_audible.csd

<CsoundSynthesizer>
<CsOptions>
-odac
</CsOptions>
<CsInstruments>
sr = 44100
ksmps = 1
nchnls = 2
0dbfs = 1

instr MassSpring
;initial values
a0        init      0
a1        init      0.05
ic        =         0.01 ;spring constant
;calculation of the next value
a2        =         a1+(a1-a0) - ic*a1
          outs      a0, a0
;actualize values for the next step
a0        =         a1
a1        =         a2
endin
</CsInstruments>
<CsScore>
i "MassSpring" 0 10
</CsScore>
</CsoundSynthesizer>
;example by joachim heintz, after martin neukom

As the next sample is calculated in the next control cycle, ksmps has to be set to 1.3 The resulting frequency depends on the spring constant: the higher the constant, the higher the frequency. The resulting amplitude depends on both, the starting value and the spring constant.

This simple model shows the basic principle of a physical modelling synthesis: creating a system which produces sound because it varies in time. Certainly it is not the goal of physical modelling synthesis to reinvent the wheel of a sine wave. But modulating the parameters of a model may lead to interesting results. The next example varies the spring constant, which is now no longer a constant:

EXAMPLE 04G03_MS_variable_constant.csd

<CsoundSynthesizer>
<CsOptions>
-odac
</CsOptions>
<CsInstruments>
sr = 44100
ksmps = 1
nchnls = 2
0dbfs = 1

instr MassSpring
;initial values
a0        init      0
a1        init      0.05
kc        randomi   .001, .05, 8, 3
;calculation of the next value
a2        =         a1+(a1-a0) - kc*a1
          outs      a0, a0
;actualize values for the next step
a0        =         a1
a1        =         a2
endin
</CsInstruments>
<CsScore>
i "MassSpring" 0 10
</CsScore>
</CsoundSynthesizer>
;example by joachim heintz

Working with physical modelling demands thought in more physical or mathematical terms: examples of this might be if you were to change the formula when a certain value of c had been reached, or combine more than one spring.

 

Implementing Simple Physical Systems

 

This text shows how to get oscillators and filters from simple physical models by recording the position of a point (mass) of a physical system. The behavior of a particle (mass on a spring, mass of a pendulum, etc.) is described by its position, velocity and acceleration. The mathematical equations which describe the movement of such a point are differential equations. In what follows, we describe how to derive time discrete system equations (also called difference equations) from physical models (described by differential equations). At every time step we first calculate the acceleration of a mass and then its new velocity and position. This procedure is called Euler's method and yields good results for low frequencies compared to the sampling rate. (Better approximations are achieved with the improved Euler's method or the Runge–Kutta methods.)

(The figures below have been realized with Mathematica)

Integrating the Trajectory of a Point 

Velocity v is the difference of positions x per time unit T, acceleration a the difference of velocities v per time unit T:

vt = (x xt-1)/T, at = (vt – vt-1)/T. 

Putting T = 1 we get

vt = x– xt-1, at = v– vt-1.

If we know the position and velocity of a point at time t – 1 and are able to calculate its acceleration at time t we can calculate the velocity vt and the position xt at time t:

vt = vt-1 at andxt = xt-1 vt

With the following algorithm we calculate a sequence of successive positions x:

1. init x and v
2. calculate a
3. v += a   	; v = v + a
4. x += v	; x = x + v

Example 1: The acceleration of gravity is constant (g = –9.81ms-2). For a mass with initial position x = 300m (above ground) and velocity v = 70ms-1 (upwards) we get the following trajectory (path) 

g = -9.81; x = 300; v = 70; Table[v += g; x += v, {16}];

                   

Example 2: The acceleration a of a mass on a spring is proportional (with factor –c) to its position (deflection) x 

x = 0; v = 1; c = .3; Table[a = -c*x; v += a; x += v, {22}];

      

Introducing damping

Since damping is proportional to the velocity we reduce velocity at every time step by a certain amount d:

v *= (1 - d)

 

Example 3: Spring with damping (see lin_reson.csd below): 

d = 0.2; c = .3; x = 0; v = 1;
Table[a = -c*x; v += a; v *= (1 - d); x += v, {22}];  

            

 

The factor c can be calculated from the frequency f:

c = 2 – sqrt(4 – d2) cos(2π f/sr) 

Introducing excitation

In the examples 2 and 3 the systems oscillate because of their initial velocity v = 1. The resultant oscillation is the impulse response of the systems. We can excite the systems continuously by adding a value exc to the velocity at every time step.

v += exc;

 

Example 4: Damped spring with random excitation (resonator with noise as input)

d = .01; s = 0; v = 0;  Table[a = -.3*s; v += a; v += RandomReal[{-1, 1}]; v *= (1 - d); s += v, {61}];

 

 

 

         

 

EXAMPLE 04G04_lin_reson.csd  

<CsoundSynthesizer>
<CsInstruments>
sr = 44100
ksmps = 32
nchnls = 1
0dbfs = 1

opcode 	lin_reson, 	a, akk
setksmps 1
avel 	init 	0 		;velocity
ax 	init 	0 		;deflection x
ain,kf,kdamp 	xin
kc 	= 	2-sqrt(4-kdamp^2)*cos(kf*2*$M_PI/sr)
aacel 	= 	-kc*ax
avel 	= 	avel+aacel+ain
avel 	= 	avel*(1-kdamp)
ax 	= 	ax+avel
	xout 	ax
endop

instr 1
aexc 	rand 	p4
aout 	lin_reson 	aexc,p5,p6
	out 	aout
endin

</CsInstruments>
<CsScore>
; 		p4 		p5 	p6
; 		excitaion 	freq 	damping
i1 0 5 		.0001   	440 	.0001
</CsScore>
</CsoundSynthesizer>
;example by martin neukom

 

 

 

Introducing nonlinear acceleration

Example 5: The acceleration of a pendulum depends on its deflection (angle x).

a = c*sin(x)

 

This figure shows the function –.3sin(x)   

                  

The following trajectory shows that the frequency decreases with encreasing amplitude and that the pendulum can turn around.

d = .003; s = 0; v = 0;
Table[a = f[s]; v += a; v += RandomReal[{-.09, .1}]; v *= (1 - d);
s += v, {400}];

          

 


We can implement systems with accelerations that are arbitrary functions of position x.

 

Example 6: a = f(x) = – c1x + c2sin(c3x) 

       

 d = .03; x = 0; v = 0;  Table[a = f[x]; v += a; v += RandomReal[{-.1, .1}]; v *= (1 - d);   x += v, {400}];
      

EXAMPLE 04G05_nonlin_reson.csd

<CsoundSynthesizer>
<CsInstruments>

sr = 44100
ksmps = 32
nchnls = 1
0dbfs = 1

; simple damped nonlinear resonator
opcode nonlin_reson, a, akki
setksmps 1
avel 	init 0			;velocity
adef 	init 0			;deflection
ain,kc,kdamp,ifn xin
aacel 	tablei 	adef, ifn, 1, .5 ;acceleration = -c1*f1(def)
aacel 	= 	-kc*aacel
avel 	= 	avel+aacel+ain	;vel += acel + excitation
avel 	= 	avel*(1-kdamp)
adef 	= 	adef+avel
	xout 	adef
endop

instr 1
kenv 	oscil 		p4,.5,1
aexc 	rand 		kenv
aout 	nonlin_reson 	aexc,p5,p6,p7
	out 		aout
endin

</CsInstruments>
<CsScore>
f1 0 1024 10 1
f2 0 1024 7 -1 510 .15 4 -.15 510 1
f3 0 1024 7 -1 350 .1 100 -.3 100 .2 100 -.1 354 1
; 		p4 		p5 	p6 	p7
;   		excitation  	c1    	damping ifn
i1 0 20   	.0001      	.01   	.00001   3
;i1 0 20  	.0001      	.01   	.00001   2
</CsScore>
</CsoundSynthesizer>
;example by martin neukom

 The Van der Pol Oscillator

While attempting to explain the nonlinear dynamics of vacuum tube circuits, the Dutch electrical engineer Balthasar van der Pol derived the differential equation


 d2x/dt= –ω2x + μ(1 – x2)dx/dt. (where d2x/dt2 = acelleration and dx/dt = velocity)


The equation describes a linear oscillator d2x/dt= –ω2x with an additional nonlinear term μ(1 – x2)dx/dt. When |x| > 1, the nonlinear term results in damping, but when |x| < 1, negative damping results, which means that energy is introduced into the system. 

Such oscillators compensating for energy loss by an inner energy source are called self-sustained oscillators

v = 0; x = .001; ω = 0.1; μ = 0.25;
snd = Table[v += (-ω^2*x + μ*(1 - x^2)*v); x += v, {200}];

         

The constant ω is the angular frequency of the linear oscillator (μ = 0). For a simulation with sampling rate sr we calculate the frequency f in Hz as

f = ω·sr/2π.

Since the simulation is only an approximation of the oscillation this formula gives good results only for low frequencies. The exact frequency of the simulation is  

f = arccos(1 – ω2/2)sr·/2π.

We get ωfrom frequency f as

2 – 2cos(f·2π/sr). 

With increasing μ the oscillations nonlinearity becomes stronger and more overtones arise (and at the same time the frequency becomes lower). The following figure shows the spectrum of the oscillation for various values of μ. 

       

Certain oscillators can be synchronized either by an external force or by mutual influence. Examples of synchronization by an external force are the control of cardiac activity by a pace maker and the adjusting of a clock by radio signals. An example for the mutual synchronization of oscillating systems is the coordinated clapping of an audience. These systems have in common that they are not linear and that they oscillate without external excitation (self-sustained oscillators). 

The UDO v_d_p represents a Van der Pol oscillator with a natural frequency kfr and a nonlinearity factor kmu. It can be excited by a sine wave of frequency kfex and amplitude kaex. The range of frequency within which the oscillator is synchronized to the exciting frequency increases as kmu and kaex increase.  

EXAMPLE 04G06_van_der_pol.csd

<CsoundSynthesizer>
<CsInstruments>

sr = 44100
ksmps = 32
nchnls = 2
0dbfs = 1

;Van der Pol Oscillator ;outputs a nonliniear oscillation
;inputs: a_excitation, k_frequency in Hz (of the linear part), nonlinearity (0 < mu < ca. 0.7)
opcode v_d_p, a, akk
setksmps 1
av init 0
ax init 0
ain,kfr,kmu xin
kc = 2-2*cos(kfr*2*$M_PI/sr)
aa = -kc*ax + kmu*(1-ax*ax)*av
av = av + aa
ax = ax + av + ain
xout ax
endop

instr 1
kaex invalue "aex"
kfex invalue "fex"
kamp invalue "amp"
kf invalue "freq"
kmu invalue "mu"
a1 oscil kaex,kfex,1
aout v_d_p a1,kf,kmu
out kamp*aout,a1*100
endin

</CsInstruments>
<CsScore>
f1 0 32768 10 1
i1 0 95
</CsScore>
</CsoundSynthesizer>

 The variation of the phase difference between excitation and oscillation, as well as the transitions between synchronous, beating and asynchronous behaviors, can be visualized by showing the sum of the excitation and the oscillation signals in a phase diagram. The following figures show to the upper left the waveform of the Van der Pol oscillator, to the lower left that of the excitation (normalized) and to the right the phase diagram of their sum. For these figures, the same values were always used for kfr, kmu and kaex. Comparing the first two figures, one sees that the oscillator adopts the exciting frequency kfex within a large frequency range. When the frequency is low (figure a), the phases of the two waves are nearly the same. Hence there is a large deflection along the x-axis in the phase diagram showing the sum of the waveforms. When the frequency is high, the phases are nearly inverted (figure b) and the phase diagram shows only a small deflection. The figure c shows the transition to asynchronous behavior. If the proportion between the natural frequency of the oscillator kfr and the excitation frequency kfex is approximately simple (kfex/kfr m/n), then within a certain range the frequency of the Van der Pol oscillator is synchronized so that kfex/kfr = m/n. Here one speaks of higher order synchronization (figure d). 

     

 

      

 

The Karplus-Strong Algorithm: Plucked String

The Karplus-Strong algorithm provides another simple yet interesting example of how physical modelling can be used to synthesized sound. A buffer is filled with random values of either +1 or -1. At the end of the buffer, the mean of the first and the second value to come out of the buffer is calculated. This value is then put back at the beginning of the buffer, and all the values in the buffer are shifted by one position. 

This is what happens for a buffer of five values, for the first five steps:

 

 initial state  1 -1 1 1 -1
 step 1  0  1 -1 1 1
 step 2  1  0 1 -1 1
 step 3  0  1 0 1 -1
 step 4  0  0 1 0 1
 step 5  0.5  0 0 1 0

 

 

The next Csound example represents the content of the buffer in a function table, implements and executes the algorithm, and prints the result after each five steps which here is referred to as one cycle:

EXAMPLE 04G07_KarplusStrong.csd

<CsoundSynthesizer>
<CsOptions>
-n
</CsOptions>
<CsInstruments>
sr = 44100
ksmps = 32
nchnls = 1
0dbfs = 1

  opcode KS, 0, ii
  ;performs the karplus-strong algorithm
iTab, iTbSiz xin
;calculate the mean of the last two values
iUlt      tab_i     iTbSiz-1, iTab
iPenUlt   tab_i     iTbSiz-2, iTab
iNewVal   =         (iUlt + iPenUlt) / 2
;shift values one position to the right
indx      =         iTbSiz-2
loop:
iVal      tab_i     indx, iTab
          tabw_i    iVal, indx+1, iTab
          loop_ge   indx, 1, 0, loop
;fill the new value at the beginning of the table
          tabw_i    iNewVal, 0, iTab
  endop

  opcode PrintTab, 0, iiS
  ;prints table content, with a starting string
iTab, iTbSiz, Sin xin
indx      =         0
Sout      strcpy    Sin
loop:
iVal      tab_i     indx, iTab
Snew      sprintf   "%8.3f", iVal
Sout      strcat    Sout, Snew
          loop_lt   indx, 1, iTbSiz, loop
          puts      Sout, 1
  endop

instr ShowBuffer
;fill the function table
iTab      ftgen     0, 0, -5, -2, 1, -1, 1, 1, -1
iTbLen    tableng   iTab
;loop cycles (five states)
iCycle    =         0
cycle:
Scycle    sprintf   "Cycle %d:", iCycle
          PrintTab  iTab, iTbLen, Scycle
;loop states
iState    =         0
state:
          KS        iTab, iTbLen
          loop_lt   iState, 1, iTbLen, state
          loop_lt   iCycle, 1, 10, cycle
endin

</CsInstruments>
<CsScore>
i "ShowBuffer" 0 1
</CsScore>
</CsoundSynthesizer>
;example by joachim heintz

This is the output:

Cycle 0:   1.000  -1.000   1.000   1.000  -1.000
Cycle 1:   0.500   0.000   0.000   1.000   0.000
Cycle 2:   0.500   0.250   0.000   0.500   0.500
Cycle 3:   0.500   0.375   0.125   0.250   0.500
Cycle 4:   0.438   0.438   0.250   0.188   0.375
Cycle 5:   0.359   0.438   0.344   0.219   0.281
Cycle 6:   0.305   0.398   0.391   0.281   0.250
Cycle 7:   0.285   0.352   0.395   0.336   0.266
Cycle 8:   0.293   0.318   0.373   0.365   0.301
Cycle 9:   0.313   0.306   0.346   0.369   0.333

It can be seen clearly that the values get smoothed more and more from cycle to cycle. As the buffer size is very small here, the values tend to come to a constant level; in this case 0.333. But for larger buffer sizes, after some cycles the buffer content has the effect of a period which is repeated with a slight loss of amplitude. This is how it sounds, if the buffer size is 1/100 second (or 441 samples at sr=44100):  

EXAMPLE 04G08_Plucked.csd

<CsoundSynthesizer>
<CsOptions>
-odac
</CsOptions>
<CsInstruments>
sr = 44100
ksmps =  1
nchnls = 2
0dbfs = 1

instr 1
;delay time
iDelTm    =         0.01
;fill the delay line with either -1 or 1 randomly
kDur      timeinsts
 if kDur < iDelTm then
aFill     rand      1, 2, 1, 1 ;values 0-2
aFill     =         floor(aFill)*2 - 1 ;just -1 or +1
          else
aFill     =         0
 endif
;delay and feedback
aUlt      init      0 ;last sample in the delay line
aUlt1     init      0 ;delayed by one sample
aMean     =         (aUlt+aUlt1)/2 ;mean of these two
aUlt      delay     aFill+aMean, iDelTm
aUlt1     delay1    aUlt
          outs      aUlt, aUlt
endin

</CsInstruments>
<CsScore>
i 1 0 60
</CsScore>
</CsoundSynthesizer>
;example by joachim heintz, after martin neukom

 

This sound resembles a plucked string: at the beginning the sound is noisy but after a short period of time it exhibits periodicity. As can be heard, unless a natural string, the steady state is virtually endless, so for practical use it needs some fade-out. The frequency the listener perceives is related to the length of the delay line. If the delay line is 1/100 of a second, the perceived frequency is 100 Hz. Compared with a sine wave of similar frequency, the inherent periodicity can be seen, and also the rich overtone structure:

Csound also contains over forty opcodes which provide a wide variety of ready-made physical models and emulations. A small number of them will be introduced here to give a brief overview of the sort of things available.

wgbow - A Waveguide Emulation of a Bowed String by Perry Cook

Perry Cook is a prolific author of physical models and a lot of his work has been converted into Csound opcodes. A number of these models wgbow, wgflute, wgclar wgbowedbar and wgbrass are based on waveguides. A waveguide, in its broadest sense, is some sort of mechanism that limits the extend of oscillations, such as a vibrating string fixed at both ends or a pipe. In these sorts of physical model a delay is used to emulate these limits. One of these, wgbow, implements an emulation of a bowed string. Perhaps the most interesting aspect of many physical models in not specifically whether they emulate the target instrument played in a conventional way accurately but the facilities they provide for extending the physical limits of the instrument and how it is played - there are already vast sample libraries and software samplers for emulating conventional instruments played conventionally. wgbow offers several interesting options for experimentation including the ability to modulate the bow pressure and the bowing position at k-rate. Varying bow pressure will change the tone of the sound produced by changing the harmonic emphasis. As bow pressure reduces, the fundamental of the tone becomes weaker and overtones become more prominent. If the bow pressure is reduced further the abilty of the system to produce a resonance at all collapse. This boundary between tone production and the inability to produce a tone can provide some interesting new sound effect. The following example explores this sound area by modulating the bow pressure parameter around this threshold. Some additional features to enhance the example are that 7 different notes are played simultaneously, the bow pressure modulations in the right channel are delayed by a varying amount with respect top the left channel in order to create a stereo effect and a reverb has been added.

EXAMPLE 04G09_wgbow.csd

<CsoundSynthesizer>

<CsOptions>
-odac
</CsOptions>

<CsInstruments>

sr      =       44100
ksmps   =       32
nchnls  =       2
0dbfs   =       1
        seed    0

gisine  ftgen	0,0,4096,10,1

gaSendL,gaSendR init 0

 instr 1 ; wgbow instrument
kamp     =        0.3
kfreq    =        p4
ipres1   =        p5
ipres2   =        p6
; kpres (bow pressure) defined using a random spline
kpres    rspline  p5,p6,0.5,2
krat     =        0.127236
kvibf    =        4.5
kvibamp  =        0
iminfreq =        20
; call the wgbow opcode
aSigL	 wgbow    kamp,kfreq,kpres,krat,kvibf,kvibamp,gisine,iminfreq
; modulating delay time
kdel     rspline  0.01,0.1,0.1,0.5
; bow pressure parameter delayed by a varying time in the right channel
kpres    vdel_k   kpres,kdel,0.2,2
aSigR	 wgbow	  kamp,kfreq,kpres,krat,kvibf,kvibamp,gisine,iminfreq
         outs     aSigL,aSigR
; send some audio to the reverb
gaSendL  =        gaSendL + aSigL/3
gaSendR  =        gaSendR + aSigR/3
 endin

 instr 2 ; reverb
aRvbL,aRvbR reverbsc gaSendL,gaSendR,0.9,7000
            outs     aRvbL,aRvbR
            clear    gaSendL,gaSendR
 endin

</CsInstruments>

<CsScore>
; instr. 1
;  p4 = pitch (hz.)
;  p5 = minimum bow pressure
;  p6 = maximum bow pressure
; 7 notes played by the wgbow instrument
i 1  0 480  70 0.03 0.1
i 1  0 480  85 0.03 0.1
i 1  0 480 100 0.03 0.09
i 1  0 480 135 0.03 0.09
i 1  0 480 170 0.02 0.09
i 1  0 480 202 0.04 0.1
i 1  0 480 233 0.05 0.11
; reverb instrument
i 2 0 480
</CsScore>

</CsoundSynthesizer>

This time a stack of eight sustaining notes, each separated by an octave, vary their 'bowing position' randomly and independently. You will hear how different bowing positions accentuates and attenuates different partials of the bowing tone. To enhance the sound produced some filtering with tone and pareq is employed and some reverb is added.

EXAMPLE 04G010_wgbow_enhanced.csd

<CsoundSynthesizer>

<CsOptions>
-odac
</CsOptions>

<CsInstruments>

sr      =       44100
ksmps   =       32
nchnls  =       2
0dbfs   =       1
        seed    0

gisine  ftgen	0,0,4096,10,1

gaSend init 0

 instr 1 ; wgbow instrument
kamp     =        0.1
kfreq    =        p4
kpres    =        0.2
krat     rspline  0.006,0.988,0.1,0.4
kvibf    =        4.5
kvibamp  =        0
iminfreq =        20
aSig	 wgbow    kamp,kfreq,kpres,krat,kvibf,kvibamp,gisine,iminfreq
aSig     butlp     aSig,2000
aSig     pareq    aSig,80,6,0.707
         outs     aSig,aSig
gaSend   =        gaSend + aSig/3
 endin

 instr 2 ; reverb
aRvbL,aRvbR reverbsc gaSend,gaSend,0.9,7000
            outs     aRvbL,aRvbR
            clear    gaSend
 endin

</CsInstruments>

<CsScore>
; instr. 1 (wgbow instrument)
;  p4 = pitch (hertz)
; wgbow instrument
i 1  0 480  20
i 1  0 480  40
i 1  0 480  80
i 1  0 480  160
i 1  0 480  320
i 1  0 480  640
i 1  0 480  1280
i 1  0 480  2460
; reverb instrument
i 2 0 480
</CsScore>

</CsoundSynthesizer> 

All of the wg- family of opcodes are worth exploring and often the approach taken here - exploring each input parameter in isolation whilst the others retain constant values - sets the path to understanding the model better. Tone production with wgbrass is very much dependent upon the relationship between intended pitch and lip tension, random experimentation with this opcode is as likely to result in silence as it is in sound and in this way is perhaps a reflection of the experience of learning a brass instrument when the student spends most time push air silently through the instrument. With patience it is capable of some interesting sounds however. In its case, I would recommend building a realtime GUI and exploring the interaction of its input arguments that way. wgbowedbar, like a number of physical modelling algorithms, is rather unstable. This is not necessary a design flaw in the algorithm but instead perhaps an indication that the algorithm has been left quite open for out experimentation - or abuse. In these situation caution is advised in order to protect ears and loudspeakers. Positive feedback within the model can result in signals of enormous amplitude very quickly. Employment of the clip opcode as a means of some protection is recommended when experimenting in realtime.

barmodel - a Model of a Struck Metal Bar by Stefan Bilbao

barmodel can also imitate wooden bars, tubular bells, chimes and other resonant inharmonic objects. barmodel is a model that can easily be abused to produce ear shreddingly loud sounds therefore precautions are advised when experimenting with it in realtime. We are presented with a wealth of input arguments such as 'stiffness', 'strike position' and 'strike velocity', which relate in an easily understandable way to the physical process we are emulating. Some parameters will evidently have more of a dramatic effect on the sound produced than other and again it is recommended to create a realtime GUI for exploration. Nonetheless, a fixed example is provided below that should offer some insight into the kinds of sounds possible.

Probably the most important parameter for us is the stiffness of the bar. This actually provides us with our pitch control and is not in cycle-per-second so some experimentation will be required to find a desired pitch. There is a relationship between stiffness and the parameter used to define the width of the strike - when the stiffness coefficient is higher a wider strike may be required in order for the note to sound. Strike width also impacts upon the tone produced, narrower strikes generating emphasis upon upper partials (provided a tone is still produced) whilst wider strikes tend to emphasize the fundamental).

The parameter for strike position also has some impact upon the spectral balance. This effect may be more subtle and may be dependent upon some other parameter settings, for example, when strike width is particularly wide, its effect may be imperceptible. A general rule of thumb here is that is that in order to achieve the greatest effect from strike position, strike width should be as low as will still produce a tone. This kind of interdependency between input parameters is the essence of working with a physical model that can be both intriguing and frustrating.

An important parameter that will vary the impression of the bar from metal to wood is

An interesting feature incorporated into the model in the ability to modulate the point along the bar at which vibrations are read. This could also be described as pick-up position. Moving this scanning location results in tonal and amplitude variations. We just have control over the frequency at which the scanning location is modulated.

EXAMPLE 04G011_barmodel.csd

<CsoundSynthesizer>
<CsOptions>
-odac
</CsOptions>
<CsInstruments>
sr     = 44100
ksmps  = 32
nchnls = 2
0dbfs  = 1

 instr   1
; boundary conditions 1=fixed 2=pivot 3=free
kbcL    =               1
kbcR    =               1
; stiffness
iK      =               p4
; high freq. loss (damping)
ib      =               p5
; scanning frequency
kscan   rspline         p6,p7,0.2,0.8
; time to reach 30db decay
iT30    =               p3
; strike position
ipos    random          0,1
; strike velocity
ivel    =               1000
; width of strike
iwid    =               0.1156
aSig    barmodel        kbcL,kbcR,iK,ib,kscan,iT30,ipos,ivel,iwid
kPan	rspline	        0.1,0.9,0.5,2
aL,aR   pan2            aSig,kPan
	outs             aL,aR
 endin

</CsInstruments>

<CsScore>
;t 0 90 1 30 2 60 5 90 7 30
; p4 = stiffness (pitch)

#define gliss(dur'Kstrt'Kend'b'scan1'scan2)
#
i 1 0     20 $Kstrt $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur >     $b $scan1 $scan2
i 1 ^+0.05 $dur $Kend $b $scan1 $scan2
#
$gliss(15'40'400'0.0755'0.1'2)
b 5
$gliss(2'80'800'0.755'0'0.1)
b 10
$gliss(3'10'100'0.1'0'0)
b 15
$gliss(40'40'433'0'0.2'5)
e
</CsScore>
</CsoundSynthesizer>
; example written by Iain McCurdy

PhISEM - Physically Inspired Stochastic Event Modeling

The PhiSEM set of models in Csound, again based on the work of Perry Cook, imitate instruments that rely on collisions between smaller sound producing object to produce their sounds. These models include a tambourine, a set of bamboo windchimes and sleighbells. These models algorithmically mimic these multiple collisions internally so that we only need to define elements such as the number of internal elements (timbrels, beans, bells etc.) internal damping and resonances. Once again the most interesting aspect of working with a model is to stretch the physical limits so that we can hear the results from, for example, a maraca with an impossible number of beans, a tambourine with so little internal damping that it never decays. In the following example I explore tambourine, bamboo and sleighbells each in turn, first in a state that mimics the source instrument and then with some more extreme conditions.

EXAMPLE 04G12_PhiSEM.csd

<CsoundSynthesizer>

<CsOptions>
-odac
</CsOptions>

<CsInstruments>

sr     = 44100
ksmps  = 32
nchnls = 1
0dbfs  = 1

 instr	1 ; tambourine
iAmp      =           p4
iDettack  =           0.01
iNum      =           p5
iDamp     =           p6
iMaxShake =           0
iFreq     =           p7
iFreq1    =           p8
iFreq2    =           p9
aSig      tambourine  iAmp,iDettack,iNum,iDamp,iMaxShake,iFreq,iFreq1,iFreq2
          out         aSig
 endin

 instr	2 ; bamboo
iAmp      =           p4
iDettack  =           0.01
iNum      =           p5
iDamp     =           p6
iMaxShake =           0
iFreq     =           p7
iFreq1    =           p8
iFreq2    =           p9
aSig      bamboo      iAmp,iDettack,iNum,iDamp,iMaxShake,iFreq,iFreq1,iFreq2
          out         aSig
 endin

 instr	3 ; sleighbells
iAmp      =           p4
iDettack  =           0.01
iNum      =           p5
iDamp     =           p6
iMaxShake =           0
iFreq     =           p7
iFreq1    =           p8
iFreq2    =           p9
aSig      sleighbells iAmp,iDettack,iNum,iDamp,iMaxShake,iFreq,iFreq1,iFreq2
          out         aSig
 endin

</CsInstruments>

<CsScore>
; p4 = amp.
; p5 = number of timbrels
; p6 = damping
; p7 = freq (main)
; p8 = freq 1
; p9 = freq 2

; tambourine
i 1 0 1 0.1  32 0.47 2300 5600 8100
i 1 + 1 0.1  32 0.47 2300 5600 8100
i 1 + 2 0.1  32 0.75 2300 5600 8100
i 1 + 2 0.05  2 0.75 2300 5600 8100
i 1 + 1 0.1  16 0.65 2000 4000 8000
i 1 + 1 0.1  16 0.65 1000 2000 3000
i 1 8 2 0.01  1 0.75 1257 2653 6245
i 1 8 2 0.01  1 0.75  673 3256 9102
i 1 8 2 0.01  1 0.75  314 1629 4756

b 10

; bamboo
i 2 0 1 0.4 1.25 0.0  2800 2240 3360
i 2 + 1 0.4 1.25 0.0  2800 2240 3360
i 2 + 2 0.4 1.25 0.05 2800 2240 3360
i 2 + 2 0.2   10 0.05 2800 2240 3360
i 2 + 1 0.3   16 0.01 2000 4000 8000
i 2 + 1 0.3   16 0.01 1000 2000 3000
i 2 8 2 0.1    1 0.05 1257 2653 6245
i 2 8 2 0.1    1 0.05 1073 3256 8102
i 2 8 2 0.1    1 0.05  514 6629 9756

b 20

; sleighbells
i 3 0 1 0.7 1.25 0.17 2500 5300 6500
i 3 + 1 0.7 1.25 0.17 2500 5300 6500
i 3 + 2 0.7 1.25 0.3  2500 5300 6500
i 3 + 2 0.4   10 0.3  2500 5300 6500
i 3 + 1 0.5   16 0.2  2000 4000 8000
i 3 + 1 0.5   16 0.2  1000 2000 3000
i 3 8 2 0.3    1 0.3  1257 2653 6245
i 3 8 2 0.3    1 0.3  1073 3256 8102
i 3 8 2 0.3    1 0.3   514 6629 9756
e
</CsScore>

</CsoundSynthesizer>
; example written by Iain McCurdy

Physical modelling can produce rich, spectrally dynamic sounds with user manipulation usually abstracted to a small number of descriptive parameters. Csound offers a wealth of other opcodes for physical modelling which cannot all be introduced here so the user is encouraged to explore based on the approaches exemplified here. You can find lists in the chapters Models and Emulations, Scanned Synthesis and Waveguide Physical Modeling of the Csound Manual.

 

  1. The explanation here follows chapter 8.1.1 of Martin Neukom's Signale Systeme Klangsynthese (Bern 2003)^
  2. See chapter 03A INITIALIZATION AND PERFORMANCE PASS for more information about Csound's performance loops.^
  3. If defining this as a UDO, a local ksmps=1 could be set without affecting the general ksmps. See chapter 03F USER DEFINED OPCODES and the Csound Manual for setksmps for more information.^

There has been error in communication with Booktype server. Not sure right now where is the problem.

You should refresh this page.